led15w 1 www.pduke.com 2014/04/30 led15w series dc-dc converter 4:1 ultra wide input range up to 15watts features applications ? no minimum load required ? 2250vdc input to output isolation ? small size and low profile 1.10 x 0.94 x 0.34 inch ? surface-mount or through-hole ? ul60950-1, en60950-1, & iec60950-1 safety approvals ? ce marked ? compliant to rohs ii & reach ? wireless network ? telecom/datacom ? industry control system ? distributed power architectures ? semiconductor equipment 2250vdc isolation remote control uvp ocp scp ovp technical specification all specifications are typical at nominal input, ful l load and 25 otherwise noted input range output voltage output current @full load input current @ no load efficiency maximum capacitor load (1) model number vdc vdc ma ma % f led15-24s3p3w 9 ~ 36 3.3 4000 60 85 12000 LED15-24S05W 9 ~ 36 5 3000 70 87 6000 led15-24s12w 9 ~ 36 12 1300 10 86 1000 led15-24s15w 9 ~ 36 15 1000 10 86 660 led15-48s3p3w 18 ~ 75 3.3 4000 40 85 12000 led15-48s05w 18 ~ 75 5 3000 40 87 6000 led15-48s12w 18 ~ 75 12 1300 10 86 1000 led15-48s15w 18 ~ 75 15 1000 10 86 660 part number structure led15 - 48 s 05 w - a series name input voltage (vdc) output quantity output voltage (vdc) input range option 24: 48: 9~36 18~75 s: single 3p3: 05: 12: 15: 3.3 5 12 15 4:1 : a: b: c: d: e: f: g: h: i: j: k: negative logic remote on/off with dip(standard) negative logic remote on/off with smt positive logic remote on/off with dip positive logic remote on/off with smt dip type without ctrl pin smt type without ctrl pin dip type, negative logic remote on/off without trim pin smt type, negative logic remote on/off without trim pin dip type without ctrl & trim pin smt type without ctrl & trim pin dip type, positive logic remote on/off without trim pin smt type, positive logic remote on/off without trim pin
led15w 2 www.pduke.com 2014/04/30 input specifications parameter conditions min. typ. max. unit operating input voltage range 24vin(nom) 48vin(nom) 9 18 24 48 36 75 vdc input reflected ripple current nominal input and fu ll load 30 map-p start-up voltage 24vin(nom) 48vin(nom) 9 18 vdc shutdown voltage 24vin(nom) 48vin(nom) 8 16 vdc start up time constant resistive load power up remote on/off 30 30 ms input surge voltage 100ms, max. 24vin(nom) 48vin(nom) 50 100 vdc positive logic (option) dc-dc on dc-dc off open or 3 ~ 15vdc short or 0 ~ 1.2vdc referred to ?vin pin negative logic (standard) dc-dc on dc-dc off short or 0 ~ 1.2vdc open or 3 ~ 15vdc remote on/off input current of ctrl pin -0.5 1.0 ma remote off input current 2.5 ma output specifications parameter conditions min. typ. max. unit voltage accuracy -1.0 +1.0 % line regulation low line to high line at full load -0.2 +0.2 % load regulation no load to full load -0.2 +0.2 % voltage adjustability (2) -10 +10 % ripple and noise measured by 20mhz bandwidth, with a 1 f m/c x7r and a 10 f t/c 100 mvp-p temperature coefficient -0.02 +0.02 %/ transient response recovery time 25% load step change 250 s over voltage protection 3.3vout 5vout 12vout 15vout 3.7 5.6 13.8 16.8 5.4 7.0 17.5 20.5 vdc over load protection % of iout rated; hiccup mode 150 % short circuit protection continuous, automatics recovery general specifications parameter conditions min. typ. max. unit isolation voltage 1 minute input to output 2250 vdc isolation resistance 500vdc 1 g isolation capacitance 1500 pf switching frequency 3.3vout, 5vout 12vout, 15vout 315 360 350 400 385 440 khz safety approvals ul60950-1 en60950-1 iec60950-1 weight 10.5g (0.36oz) mtbf mil-hdbk-217f, full load 2.444 x 10 6 hrs environmental specifications parameter conditions min. typ. max. unit operating ambient temperature with derating -40 +120 storage temperature range -55 +125 thermal shock mil-std-810f vibration mil-std-810f relative humidity 5% to 95% rh lead-free reflow solder process ipc j-std-020d moisture sensitivity level(msl) ipc j-std-033b level 2a emc specifications parameter conditions level emi (3) en55022 class a, class b radiated immunity en61000-4-3 10 v/m perf. criteria a fast transient (4) en61000-4-4 2kv perf. criteria a surge (4) en61000-4-5 1kv perf. criteria a conducted immunity en61000-4-6 3 vr.m.s perf. criteria a
led15w 3 www.pduke.com 2014/04/30 note: 1. test by minimum input and constant resistive load. 2. trimming allows the user to increase or decrease th e output voltage set point of the module. this is a ccomplished by connecting an external resistor between the trim pin and either +vout pin or -vout pin. 3. the standard modules meet en55022 class a and class b with external components. for further informatio n, please contact with p-duke. 4. an external input filter capacitor is required if t he module has to meet en61000-4-4, en61000-4-5. the filter capacitor power mate suggest: nippon che mi-con ky series, 220 f/100v. caution: this power module is not internally fused. an input line fuse must always be used. characteristic curve led15-48s05w derating curve led15-48s05w efficiency vs. input voltage led15-48s05w efficiency vs. outp ut load mechanical drawing dip type smt type pin connection external output trimming 1. all dimensions in inch (mm) 2. tolerance :x.xx0.02 (x.x0.5) x.xxx0.01 (x.xx0.25) 3. pin pitch tolerance 0.01 (0.25) 4. pin dimension tolerance 0.004(0.1) pin define 1 +vin 2 -vin 3 ctrl 4 +vout 5 trim 6 -vout output can be externally trimmed by using the method shown below. 6 5 trim up r u 5 4 trim down r d
|
